Section 4.4 Switch IP Configuration

Unlock all answers in this set

Unlock answers
question
You have a small network connected to the Internet as shown in the Exhibit. You need to configure the default gateway address on Wrk1 so that it can communicate with the hosts on the Internet. Which address would you use for the default gateway address?
answer
The IP address assigned to Fa0/0 on Router 1
question
You have a small network as shown in the Exhibit. You have configured the IP address and subnet mask on Wrk1. You want to be able to use Wrk1 to browse the Internet to connect to sites like www.cisco.com. What other parameters are required on the workstation? (Select two.)
answer
Default gateway DNS server address
question
You have a small network with a single subnet connected to the Internet as shown in the Exhibit. The router has been assigned the two addresses shown. You need to manually configure the workstation to connect to the network. The workstation should use RouterA as the default gateway, and DNS1 as the DNS server address. From the drop-down lists, select the appropriate paramteres to configure the workstation's TCP/IP settings.
answer
IP Address: 192.168.12.46 Subnet Mask: 255.255.255.240 Default Gateway: 192.168.12.34 DNS Server: 192.162.1.22
question
Which command(s) would you use to configure a default gateway on a Catalyst 2950XL switch?
answer
Switch (config) #ip default-gateway 192.168.10.1
question
You must configure an IP address on a Catalyst 2950XL switch using the default management switch port. From global configuration mode, which commands would you enter to configure the correct management port?
answer
int vlan 1 ip address 192.168.10.2 255.255.255.0
question
You are the only network administrator for your company. You are planning for an upcoming vacation and need to ensure that you can administer your switches remotely while you are gone. What must you configure to allow remote administration? (Choose two.)
answer
The switch must be configured with a valid IP address and default gateway. The remote workstations must have access to the management VLAN of the switch.
question
You have a workstation configured with DNS server addresses as follows: Primary DNS server = 192.168.1.1 Alternate DNS server = 192.168.1.155 While browsing the Internet, you go to www.cisco.com. A few minutes later, you type ping www.cisco.com into a command prompt. How will the workstation get the IP address for www.cisco.com?
answer
Out of its local DNS cache
question
Listed below are several places that a workstation checks to resolve DNS host names. A. Primary DNS server B. Secondary DNS servers C. HOSTS file D. Local DNS cache In a browser, you type the name of a website. In which order will these locations be checked during teh name resolution process?
answer
D, C, A, B
question
You would like to see what host names have been cached on your router. Which command displays the cached list of host names?
answer
Show hosts
question
For each operation on the right, match the appropriate command from the list on the left.
answer
Configure DNS server address for the router to use for resolve host names: ip name-server Create static entries for hosts, associating a host name with an IP address: ip host Prevent the router from using DNS to resolve host names: no ip domain-lookup Set the DNS name used by the router: hostname
question
You have just started a Cisco 2960 switch. You notice that the system light is a solid amber color. What does this indicate?
answer
The system has power but is not functioning properly.
question
You are checking the status of port Fa0/12 on your Cisco 2960 switch. A cable has been plugged in to the port and is connected to a device. You press the Mode button to select Stat, Duplex, and Speed. Each time the port light remains off. Which of the following is true?
answer
The port is shut down or the cable is bad.
question
You are checking the status of port Gi0/1 on your Cisco switch. A cable has been plugged in to the port and is connected to a device. You press the Mode button to select Stat, Duplex, and Speed. The results are shown below: Stat = Flashing green. Duplex = Solid green. Speend = Flashing green. Which of the following are true? (Select two.)
answer
The port is operating in full-duplex mode. The port speed is 1000 Mbps.
question
Wrk1 is connected to port Fa0/16 on your Cisco 2960 switch. The user complains that she can't access the network server. You verify that a cable is connected to the Fa0/16 port on the switch. You press the Mode button to select Stat, Duplex, and Speed. Each time the port light remains off. Which command would most likely correct the problem?
answer
no shutdown
question
Wrk1 is connected to port Fa0/16 on your Cisco 2960 switch. A cable has been plugged in to the port and is connected to a device. You press the Mode button to select Stat, and the port light alternately flashes amber green. What should you do to correct the problem?
answer
Check the NIC in Wrk1 for frame errors or excessive collisions.
Get an explanation on any task
Get unstuck with the help of our AI assistant in seconds
New