Chapter 16 Milady Denham Springs Beauty College Rias class
Unlock all answers in this set
Unlock answersquestion
A good haircut serves as the________ for attractive hairstyles and other services performed in the salon
answer
Foundation
question
A technique of using diagonal lines by cutting hair ends with a slight increase or decrease in length is called:
answer
Beveling
question
Cutting the hair straight across the Strand where the lengths of the hair all come to one hanging level, forming a weight line, is known as:
answer
Blunt cutting
question
Cutting with the points of the shears to create texture in the hair is known as:
answer
Notching or Point cutting
question
When they graduated shape, or wedge, has a stacked area around the exterior and his cut at low to medium elevations, it is known as:
answer
Graduated
question
The section of hair that determines the length the hair will be cut is called the:
answer
Guide
question
How tightly the hair is pulled when cutting is referred to as:
answer
Tension
question
The level at which a blunt cut Falls is called the:
answer
Weight line
question
If the hair is cut while parts are partly wet and parts are partly dry, the results will be:
answer
Uneven
question
If you cut one parting with light tension and the next parting with heavy tension, the results will be:
answer
Poorly Blended
question
Palming the shares during haircutting reduces strain on the index finger and_____ while combing the hair
answer
Thumb
question
In hair cutting, why is it necessary to always comb each parting from the scalp to the guide and remove all Tangles and distribute the hair evenly in The Parting?
answer
To ensure an even cut
question
To ensure even results in the finished haircut, always maintain an even amount of ______in the hair
answer
Moisture
question
The Implement mainly used to remove bulk from the hair is known as:
answer
Thinning shear
question
Implement used to create very short tapers quickly is the:
answer
Clipper
question
What Implement is used to create clean lines around the perimeter of a short taper?
answer
Edger
question
The Triangular section of hair that begins at the Apex and into the front Corners is known as the:
answer
Fringe
question
The method of manufacturing shears whereby molten steel is poured into a mold and cooled is called:
answer
Casting
question
When the scissor is held with the ring and Little Fingers of the opposite hand while the hair is combed, it is called:
answer
Palming the shear
question
When the hair is parted from the center of the forehead to the center of the nape and then parted from the crown down to the ears, it is known as:
answer
Four Section parting
question
What is necessary to help control the hair and produce a more uniform cut?
answer
Sectioning
question
The direction in which the hair grows from the scalp is called the______.
answer
Growth pattern
question
The_______ of the hair will determine the size of the subsection when cutting.
answer
Density
question
The angle or degree at which a subsection of hair is held or elevated from the head when cutting is called.
answer
Elevation
question
The guide that creates two lines seen around the perimeter of the cut is called the:
answer
Exterior guide
question
When hair is layered and a high elevation, what Guide has used?
answer
Interior guide
question
A guide that is directed to the next parting to be cut is called a:
answer
Travel guide
question
What will result if the head is not held in a consistent position when cutting the back and side sections?
answer
An uneven cut
question
Always take consistent and clean______ to insure an even amount of hair in each subsection and produce more precise results.
answer
Partings
question
The highest point of the head is known as the____
answer
Apex
question
Zero degree elevation cut is also known as:
answer
Low elevation
question
A 90-degree elevation cut is also known as
answer
High elevation
question
180 degree elevation cut is also known as
answer
Long layered haircut
question
The widest area of the head, starting at the temples and ending at the bottom of the crown, is known as the?
answer
Parietal ridge
question
When cutting a zero degree, low elevation or blunt cut the hair is
answer
Combed straight down and cut parallel to the floor
question
When cutting a high-elevation cut the hair is held at______ from the head and cut to the desired length
answer
90 degrees
question
Upon completion of the high elevation cut the hair should be_____when measured.
answer
The same length
question
What type of parting or subsections are used when checking a haircut?
answer
Partings opposite to those used when cutting
question
The area of the head between the Apex and the back of the parietal ridge is known as the____
answer
Crown
question
The angle at which the fingers are held when cutting the line that creates the end shape is known as the________
answer
Cutting line
question
Method of cutting or thinning the hair using razor sharp shears is____
answer
Slide cutting
question
The main purpose of thinning the hair is to:
answer
Remove bulk not weight
question
A versatile tool which is used to create a softline when cutting is the:
answer
Razor
question
When cutting with a razor it is essential to:
answer
Keep the hair damp
question
When you comb the hair away from its natural falling position rather than straight out from the head toward a guideline it is called_______
answer
Overdirection
question
The amount of pressure applied when combing and holding a subsection is called.
answer
Tension
question
Cutting____ means that the palm of both hands are facing each other while cutting.
answer
Palm-to-palm
question
Layers create movement and volume in the hair by_____
answer
Releasing weight
question
The process of removing excess bulk without shortening the length is called____
answer
Texturizing
question
When removing length from facial hair, the_____is used to control the hair.
answer
Comb
