Quiz Ch 3, 4 – Flashcards
Unlock all answers in this set
Unlock answersquestion
Which network component connects a device with the transmission media and allows it to send and receive messages?
answer
Network Interface Card
question
What is the proper format of a MAC address?
answer
00-00-00-00-00-00(- can also be replaced with .)
question
A host wants to send a message to another host with the IP address 115.99.80.157. IP does not know the hardware address of the destination device. What protocol can be used to discover the MAC address?
answer
ARP
question
What type of module might a switch use to allow it to modify the media type supported by a switch port?(2 answers)
answer
SFP, GBIC
question
Which OSI model layer does a media converter operate?
answer
Layer 1
question
You have a server that has a 100BaseFX network interface card that you need to connect to a switch. The switch only has 100BaseTX ports.
answer
Media converter
question
Which of the following is true about the MAC address?(2 answers)
answer
It is typically represented by hexadecimal numbers. It is a 48 bit address.
question
Which of the following statements accurately describes how a modem works?(2 answers)
answer
It demodulates analog data from a telephone network into digital PC data. It modulates digital data from the PC into analog data and transmits it on a telephone network.
question
What device sends signals from a computer onto a network?
answer
Transceiver
question
Which of the following devices is used on a LAN and offers guaranteed bandwidth to each port?
answer
Switch
question
An 8-port switch receives a frame on port number. The frame is addressed to an unknown device. What will the switch do?
answer
Send the frame out ports 2-8
question
Which of the following devices operate at the OSI model layer 2?(2 answers)
answer
Network Interface Card, Switch
question
Which of the following devices is used on a LAN and offers guaranteed bandwidth to each port?
answer
Switch
question
Your company purchases a new bridge, which filters packets based on the MAC address of the destination computer. On which layer of the OSI model is the device functioning?
answer
Data Link
question
An access point that conforms to the IEEE 802.11b standard acts most closely to what other networking device?
answer
Hub
question
A switch is associated with which OSI model layer?
answer
Data Link
question
Which of the following best describes how a switch functions?
answer
It connects multiple cable segments (or devices) and forwards frames to the appropriate segment.
question
At which layer of the OSI model do hubs operate?
answer
Physical
question
How do switches and bridges learn where devices are located on a network?
answer
When a frame enters a port, the source MAC address is copied from the frame header.
question
Which of the following hardware devices regenerates a signal out all connected ports without examining the frame or packet contents?(2 answers)
answer
Repeater, Hub
question
What are three devices that operate at the Data Link layer of the OSI model?
answer
Switches, Network Interface Cards, Bridges
question
At which of the following OSI layers does a router operate?
answer
Layer 3
question
Which of the following is the best device to deploy to protect your private network from a public untrusted network?
answer
Firewall
question
Which of the following hardware devices links multiple networks and directs traffic between networks?
answer
Router
question
Name two tasks that routers perform.
answer
Maintain information about paths through an internetwork. Route data based on logical network addresses
question
You are the administrator of a company's network. You want to prevent unauthorized access to your intranet from the internet. Which of the following should you implement?
answer
Firewall
question
At what OSI layer does a router operate to forward network messages?
answer
Network
question
You are the network administrator for a small organization. Recently, you contacted an ISP to connect your organization's network to the internet to provide users with internet access. Since doing so, it has come to your attention that an intruder has invaded your network on three separate occasions. What type of network hardware should you implement to prevent this from happening again?
answer
Firewall
question
Which of the following physical topologies are used with Ethernet networks?(2 answers)
answer
Bus, Star
question
A network is connected following the IEEE 802.3 specifications. Which of the following best describes when a device can transmit messages?
answer
The device listens to determine if the transmission media is free.
question
Which of the following connectors is used with Ethernet 10BaseT networks?
answer
RJ-45
question
The media access control method of all Ethernet networks is
answer
CSMA/CD
question
Which of the following use the CSMA/CD access method?(2 answers)
answer
1000BaseT, 10BaseT
question
You want to implement an Ethernet network at very long distances using fiber optic cables. Which standard and cable type would you choose?(2 answers)
answer
1000BaseLX, 1000BaseSX
question
You have been tasked with designing a high-speed Ethernet network. Your client's building already has 150ohm shielded twisted pair wiring installed. Due to budget constraints, they have asked you to reuse the existing wiring instead of installing new fiber optic cabling. Which Ethernet standard could you implement in this situation?
answer
1000BaseCX
question
Your network follows the 100BaseTx specifications for Fast Ethernet. What is the maximum cable segment length allowed?
answer
100 meters
question
Which of the following Ethernet standards uses fiber-optic cabling?(2 answers)
answer
100BaseFX, 1000BaseLX
question
You have been tasked with designing an Ethernet network. Your client needs to implement a very high-speed network backbone between campus buildings; some of which are around 300 m apart. Multimode fiber-optic cabling has already been installed between buildings. Your client has asked that you use the existing cabling. Which Ethernet standard meets these guidelines?(2 answers)
answer
1000BaseSX, 10GBaseSR
question
Which of the following are requirements of the 1000BaseT Ethernet standards?(3 answers)
answer
CAT 5e cabling, RJ-45 connectors, The cable length must be less than or equal to 100m
question
Which Gigabit Ethernet standard uses multimode fiber-optic cabling and supports network segments up to a maximum of 550 m long?
answer
1000BaseSX
question
What type of cabling is used with 100BaseTX Fast Ethernet networks?
answer
Type 1A STP or Category 5 UTP
question
What is the minimum cable specification that supports 1000 Mbps Ethernet?
answer
Cat 5
question
What topology is used with 100BaseTX Fast Ethernet networks?(2 answers)
answer
Physical star/logical bus, Physical star/logical star
question
Which Gigabit Ethernet standard can support long network segments up to a maximum of 5 km when used with single mode fiber-optic cable?
answer
1000BaseLX
question
Ethernet 100BaseFX networks use what type of cabling?
answer
Fiber-optic
question
Your network follows the 100BaseFX specifications for Fast Ethernet, and uses half-duplex, multimode cable. What is the maximum cable segment length allowed?
answer
412 meters
question
Which of the following standards is used by SONET?
answer
10GBaseLW
question
You are planning a network for an educational campus. Due to the size of the buildings and the distance between them, you have elected to use 10BaseFL hubs, cabling, and network interface cards. What is the maximum length for the network cable between a workstation and a hub?
answer
2000 meters
question
With an Ethernet 10BaseT network, the maximum cable length between a computer and the hub is:
answer
100 meters
question
You would like to implement 10 Gbps Ethernet over a distance of 1 km or greater. Which of the following would be the minimum requirement for the implementation?(2 answers)
answer
10GBaseLR standards, Single mode fiber
question
Which of the following standards is typically used in a rollover cable?
answer
RS-232
question
You need to connect to a workstation to a switch using a regular port on the switch (not an uplink port). The switch does not support auto-MDI. Which type of cable should you use?
answer
Straight through
question
Which of the following connectors is typically used on one end of a rollover cable?
answer
Serial
question
You need to transfer data from one laptop to another and would like to use an Ethernet cable. You do not have a hub or a switch. Which type of cable should you use?
answer
Crossover
question
You want to connect the LAN port on a router to the uplink port on a switch. The switch does not support auto-MDI. Which type of cable should you use?
answer
Crossover
question
You want to create a rollover cable that has an RJ-45 connector on both ends. How should you connect the wires within the connectors?
answer
Connect pin 1 to pin 8, pin 2 to pin 7, pin 3 to pin 6, and pin 4 to pin 5
question
You have two switches that you need to connect using their uplink ports. The switches do not support auto-MDI. Which type of cable should you use?
answer
Crossover
question
You have purchased a new router that you need to configure. You need to connect a workstation to the router's console port to complete the configuration tasks. Which type of cable would you most likely use?
answer
Rollover.
question
What is the main difference between RIP and RIP2?
answer
RIP uses classful protocol, while RIP2 is classless protocol.
question
You have a private network connected to the internet. Your routers will not share routing information about your private network with Internet routers. Which of the following best describes the type of routing protocol you would use?
answer
IGP
question
Which of the following routing protocols divides the network into areas, with all networks required to have an area 0 (area 0 identifying the backbone area)?
answer
OSPF
question
You have a network configured to use the OSPF routers have learned about all other routes in the network?
answer
convergence
question
Which of the following protocols has a limit of 15 hops between any two networks
answer
RIP
question
You have a router configured to share routing information using RIP. In addition, you have a single static route that identifies a default route for all other networks?
answer
Manually reconfigure the default route to point to the new next hop router.
question
Which of the following is a characteristic of static routing when compared to dynamic routing?
answer
All routers must be manually updated on the router.
question
What information does the next hop entry in a routing table identify?
answer
The first router in the path to the destination network.
question
Which of the following routing protocols are classified as a link state routing protocols?
answer
IS-IS, OSPF
question
What are the main differences between the OSPF and IS-IS routing protocols?
answer
OSPF requires an area 0, while IS-IS does not.
question
Which of the following best describes OSPF?
answer
ospf is a classless link-state routing protocol
question
A router is connected to a network 192.169.1.0/24 and network 192.168.2.0/24. The router is configured to use RIP and has learned of networks 192.168.3.0/24 and 192.168.4.0/24. The router is also configured with a static route of 0.0.0.0 with a mask of 0.0.0.0. The router receives a packet addressed to the network 10.1.0.0/16. What will the router do with the packet.
answer
Forward the packet to the next hop router specified by the route network 0.0.0.0
question
You manage a server that uses an IP address of 192.168.255.188 with a mask of 255.255.0.0 Which of the following describes the address type?
answer
Classless
question
Which of the following routing protocols is used by routers on the Internet for learning and sharing routes?
answer
BGP
question
Which of the following terms are often synonymous with or made possible with CIDR?
answer
Classless, VLSM
question
Under which of the following circumstances might you implement BGP on your company network and share routes with Internet routers?
answer
If the network is connected to the Internet using multiple ISPs.
question
Which of the following statements about RIP is true?
answer
RIP uses hop counts as the cost metric.
question
A router is connected to network 192.168.1.0/24 and network 192.168.2.0/24. The router is configured to use RIP and has learned of networks 192.168.3.0/24 and 192.168.4.0/24.
answer
Wait for convergence to take place.
question
A router is connected to a network 192.168.1.0/24 and network 192.168.2.0/24. The router is configured to use RIP and has learned of networks 192.168.3.0/24 and 192.168.4.0/24. There is no default route on router. The router receives a packet addressed to network 10.1.0.0/16. What will the router do with the packet?
answer
Drop the packet.
question
Which of the following protocols is classified as a balanced hybrid routing protocol?
answer
EIGRP
question
You have a computer that is connected to the internet through a NAT router. You want to use a private addressing scheme for your computer. Which of the following IP addresses could you assign to the computer? (Three answers)
answer
10.0.12.15, 192.168.12.253, 172.18.188.67
question
Which of the following is not one of the ranges of IP addresses defined in RFC 1918 that are commonly used behind a NAT server?
answer
169.254.0.1-169.254.255.254
question
Your computer has an IP address of 161.13.5.15. Your computer is on a:
answer
Public network
question
Which organization is responsible for allocating public IP addresses?
answer
IANA
question
Which of the following IP addresses is a valid IP address for a host on a public network?
answer
142.15.6.1
question
You have a small network at home that is connected to the internet. On your home network you have a server with the IP address of 192.168.55.199/16. YOu have a single public address that is shared by all hosts on your private network. You want to configure the server as a web server and allow internet hosts to contact the server to browse a personal web site. What should you use to allow access?
answer
Static NAT
question
Which of the following associates a port number with a host on a private network?
answer
PAT
question
You have a small network athome tht is connected to the Internet. On your home network yu have a server with the IP address of 192.168.55.199/16. All computers on your homenetwork can connect to the internet. From your work office, you try to access your home computer using it's IP address, but are unable to communicate with the server. You are able to connect to other hosts on the Internet. Why can't you access the server?
answer
Private addresses are not accessible through the internet.
question
Which of the following is a valid IPv6 address?
answer
FEC0::AB:9007
question
Which of the following are valid IPv6 addresses. (Two answers)
answer
6384:1319:7700:7631:446A:5511:8940:2552, 141:0:0:0:15:0:0:1
question
Which type of address is the IP address 198.162.12.254/24?
answer
Unicast
question
Which type of address is used in a packet to address the packet to a single host?
answer
Unicast
question
Which type of address is the IP address is the IP address 232.111.255.250?
answer
Multicast
question
Which protocol does an IP host use to inform a router that it wants to receive specific multicast frames?
answer
IGMP
question
Which of the following address types is shared by multiple hosts, and is used to form groups of computers that should receive the same data stream?
answer
Multicast
question
Which of the following protocols are used with VoIP (Two answers)
answer
SIP, RTP
question
Which of the following features is used with digital IP phones to supply power through a switch port?
answer
PoE
question
Which of the following protocols is used by VoIP to set up, maintain, and terminate a phone call?
answer
SIP
question
Which component is most likely to allow physical and virtual machines to communicate with each other?
answer
Virtual switch
question
What type of virtualization completely simulates a real physical host?
answer
Full virtualization
question
In virtualization, what is the role hypervisor?
answer
A hypervisor allows virtual machines to interact with the hardware without going through the host operating system.
question
You need to provide DHCP and file share services to a physical network. These services should be deployed using virtualization. Which type of virtualization should you implement?
answer
Virtual servers
question
All of the 802.11 standards for the wireless networking support which type of communication path sharing technology?
answer
CMSA/CA
question
Which of the following are frequencies defined 802.11 committees for wireless networking? (select 2)
answer
2.4 GHz, 5.75GHz
question
What is the frequency of 802.11a networking?
answer
5.75GHz
question
How many total channels are available for 802.11g wireless networks?
answer
11
question
You have been contacted by OsCorp to recommend a wireless Internet solution. The wireless strategy must support transmission range of 150 ft, use a frequency range of 2.4GHz, and provide the highest possible transmission speeds. Which of the following wireless solutions would you recommend?
answer
802.11g
question
Which IEEE wireless standards specify transmission speeds up to 54Mbps?(Select 2)
answer
802.11a, 802.11g
question
You are designing a wireless network for a client. Your client needs the network to support a data rate of at least 54Mbps. In addition, the client already has a wirelesss telephone system installed that operates 2.4GHz. Which 802.11 standard will work best in this situation?
answer
802.11a
question
You are designing an update to your clients wireless network. The existing wireless network uses 802.11b equipement; which your client complains runs to slowly. Due to budget constraints she wants to upgrade only the wireless access points in the network this year. Next year, she will upgrade the wireless network boards in her users' workstations. She has also indicated that the system must continue to function during the transition period. Which 802.11 standard will work best in this situation?
answer
802.11g
question
Which data transmission rate is defined by the IEEE 802.11b wireless standard?
answer
11 Mbps
question
How many total channels are avaible for 802.11a wireless networks?
answer
23
question
Which IEEE standard describes wireless communication?
answer
802.11b
question
You need to add security for your wireless network. You would like to use the most secure method. Which method should you implement?
answer
WPA2
question
Which of the following wireless security methods uses a common shared key configured on the wireless access point and all wireless client?
answer
WEP, WPA, Personal, and WPA2 Personal
question
You want to implement 802.1x authentication on your wireless network. Where would you configure passwords that are used for authentication?
answer
On a RADIUS server
question
Which of the following specifications identify security that can be added to wireless networks?
answer
802.1x, 802.11i
question
What encryption method is used by WPA for wireless networks?
answer
TKIP
question
You want implement 802.1x authentication on your wireless network. Which of the following will be required?
answer
RADIUS
question
Which of the following protocols or mechanisms is NOT used to provide security on a wireless network?
answer
RDP
question
On wireless networks, which technology is employed to provide the same type of protection that cables provide on a wired network?
answer
WEP
question
On a wireless network that is employing WEP, which type of users are allowed to authenticate through the access points?
answer
Users with the correct WEP key
question
You have a small home wireless network that uses WEP. The access point is configured as the DHCP server and a NAT router that connects to the Internet. You do not have a RADIUS server. Which authentication method should you choose?
answer
Open
